Diode-led K-RANGE 24 LED Tape Light Manuel d'utilisateur télécharger pdf

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

1 OF 4

K-RANGE 24

™

24V TUNABLE WHITE LED TAPE LIGHT

Do not bend LED strip light on a

horizontal plane.

Do not fold or crease LED strip light.Do not bend LED strip light to a diameter

less than 1.5 inches.

Do not put excessive pressure on surface of

strip light (e.g. glass/acrylic panes etc.).

1.5 in.

Do not cover strip light with any materials. Do not power strip light while

aached to spool or ghtly coiled.

• Install in accordance with the Naonal Electric Code and local

regulaons.

• This product is intended to be installed and serviced by a qualied,

licensed electrician.

• DO NOT connect tape directly to 120VAC power.

• To meet the tape ETL Lisng cercaon, tape light must be powered

with a compable Class 2 DC constant voltage LED driver (power

supply).

• Each LED driver is unique and may require a proper load derang,

which is dependent to the installed ambient temperature environment.

Refer to each driver specicaon sheet for full power rangs & load

derangs.

• Do not power tape light while aached to plasc spool or ghtly coiled.

Excess heat may melt the spool and/or cause damage to the tape.

• Do not install tape light in direct sunlight.

• Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Inadequate wire installaon could overheat wires, and cause a re.

• Tape light, aached wire leads, and addional extension cables,

connectors, etc., are not rated for in-wall installaon unless otherwise

noted. Connectors have a Class 2 amp limit unless otherwise noted.

• Tape light must be handled with care. Excessive handling, bending, and

pressure may damage the product, voiding the warranty.

• Each tape light has a dierent power consumpon rang and maximum

run length that must be individually wired to a compable low voltage

(PWM) control or DMX decoder. Refer to the tape light packaging label

or specicaon sheet for further technical informaon.

Safety & Warnings

Tape Light Handling

DO NOT CONNECT

TO HIGH VOLTAGE

Dry Location Only

Dimmable

24V

Adjustable Kelvin

Quick Specs

Included Model(s) DI-24V-KRNG-7020

Ambient Temperature † -4° ~ 122°F (-20° ~ 50°C)

Environment Indoor / dry locaon

Input Voltage 24V DC constant voltage

Power Consumpon

Max: 2.92W / 122mA per foot

For full specicaons, see the ‘Specicaon Sheet’ available at the online

product page.

†

Do not install product in an environment outside the listed ambient

temperature. Ensure adequate airow and heatsinking is considered

when mounng/installing.

DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!

Read all warnings and installaon instrucons thoroughly.

WARNING

IG082514-1.3

1 2 3 4

1.877.817.6028 1
QUESTIONS? 4

Résumé du contenu

Page 1 - 1.877.817.6028

[email protected] www.DiodeLED.comINSTALLATION GUIDE1 OF 4K-RANGE 24™ 24V TUNABLE WHITE LED TAPE LIGHT®Do not bend LED

Page 2

[email protected] www.DiodeLED.comINSTALLATION GUIDE2 OF 4K-RANGE 24™ 24V TUNABLE WHITE LED TAPE LIGHT®A. Cut the tape

Page 3

[email protected] www.DiodeLED.comINSTALLATION GUIDE3 OF 4K-RANGE 24™ 24V TUNABLE WHITE LED TAPE LIGHT®++ +−− −+−Cut p

Page 4 - QUESTIONS?

[email protected] www.DiodeLED.comINSTALLATION GUIDE4 OF 4K-RANGE 24™ 24V TUNABLE WHITE LED TAPE LIGHT®The following di

Commentaires sur ces manuels

Pas de commentaire

Diode-led K-RANGE 24 LED Tape Light Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Diode-led K-RANGE 24 LED Tape Light. Diode LED K-RANGE 24 LED Tape Light User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Diode-led K-RANGE 24 LED Tape Light